机器 - 進出口

Model Number: OKABFKJ-1 AC Voltage: 220 or 110V Ampoule size: 1- 75ml Filling Flow range: 0.007-2280ml/min Filling Speed: 0.1-600rpm Filling Accuracy: <0.5% Peristaltic pump + OH400 oxyhydrogen generator +OKRFH-2 rotary ampoule sealing torch device Suitable for pharmaceuticals, cosmetics, chemicals, laboratories, universities, etc.

Oxyhydrogen gas flame temperature 2800℃ Blowing glass tube lathe oxyhydrogen generator vacuum pump 1.It is designed for super dry and clean cuts from glass tube diameter 8-150 mm and cutting lengths 20-400mm. 2. Energy-saving gas generator, no gas cylinder. It can replace acetylene, coal gas, liquefied gas, etc. No pollution, high-efficiency sealing, energy saving and, convenience.

OH1000 produces 1000 liters per hour of Oxyhydrogen gas OK-M210 vacuum seal glass tube Quartz Tube diameter: φ6 to φ40 Tube length: ＜40cm Noble gas interface: Yes Isolation valve: Yes Backflow preventer: Yes Vacuum pump: mechanical or molecular pump Vacuum pump Joint: KF25

管道清洗机器人可代替人工进入管道清洗,解决了人们对油污粘在身上的烦恼,可以用机器人进入管道清洗,也可解决狭小空间无法清洗的烦恼,危险难度也降低了

Weight: 20-150T Applicable device: vertical mills, mineral slag vertical mills, cement vertical mills, steel slag vertical mills, nickel slag mills, raw material vertical mills and coal vertical mills. Application: Cement, building material, chemical, coal, electricity, metallurgy, non metallic mine and others Customizable: Yes Main materials: Plain carbon steel, Si-Mn steel Product Introduction Mill table is an important part of cement vertical mill and slag vertical mill. Mill table consists of resistance loop, liner plate and base. SHANGHAI SPECIAL METAL CO., LTD optimizes casting technology of mill table, applies the most advanced molding - sodium silicate-bonded sand. Our technology overcomes structural shortcomings of traditional methods. The advantages are base of mill table is uniformly stressed; nip angle between mill table and mill roller is enlarged, good anti-corrosion of no wear-resisting face. SHANGHAI SPECIAL METAL CO.

Aluminum electrolyzer is the main equipment of Cryolite- Aluminum Oxide mix in the fused salt solution in order to electrolysis the fine aluminum to get the aluminum ingot. Electrolytic aluminum anode steel claw/yoke is also called electrolysis claw/yoke. There are several types of claws, such as parallel three claws, four claws, stereoscopic four claws, six claws, eight claws, double anode steel claw etc. The steel claw is connected to the copper bar to consist of Anode. Material for the claw/yoke is an approved low carbon steel, which is similar the following standards: AS 2074-2003 Grade C2 AISI 1010, 1008 or 1006

Shanghai Special Metal Co., Ltd supplies ball mill head. The materials of mill head are normally selected low carbon steel and low alloy steel. It's produced by casting, used in ball grinding mill, including the feed end and outlet end, our head/cap for the bellow ball grinding mill.

The main equipment of producing pellet by rotary kiln are chain grating machine, rotary kiln and circular cooler. And the chain grating machine is the most important equipment. Chain grating machine’s main part is grate bed, which is to dry and preheat pellet by remained heat flow. Grate bed consists of chain link, grate plate, side plate, pipe spacer and protecting sleeve. Grate plate is shaped and casted by .heat-resisting alloy steel, its casting tolerance is CT6. The grate plate castings cycle through the grate furnace on a continuous cycle and carry the magnetite iron ore pellets through the process and into the kiln. The maximum temperature of the grate plate goes to approximately 650℃ when it discharges its load into the kiln and then the castings cool down to approximately 150℃ in free air, as it returns to the tail end.

Crucibles are cast steel molds for the casting of aluminum ingot for remelt storage and/ or transportation. Dimensions and design can be customized to customer requirements, including the casting of customer’s logo, and additional of feet and/or lugs for material handling. INDUSTRIES : Cast houses; Remelter APPLICATIONS : Cast ingot Solid storage/ transportation Empty trough / furnace MATERIAL AVAILABLE : QT450-12/ASTM A536/65-45-12 Shanghai Special Metal Co., Ltd is a comprehensive and professional supporting supplier in industrial field which owns great production capacity, advanced management ability, splendid procedure control system and first rate service so that we can provide high quality products as well as service to the worldwide customers. In principle there are three sorts of materials available for the manufacture of crucibles: Grey Cast Iron, Spheroidal Graphite (S.G.) Iron and Cast Steel.

Slag pots are crucial items as they are part of lifting equipment and therefore undergo in terms of mechanical design engineering and handling the national safety regulations of the state where they are supposed to be operated. Thus, the following design criteria must be taken into consideration: Type of furnace that the slag pot will service, Quantity and type of slag generated, Method of handling and dumping the pot, Heat impact during operation, Dimensional restrictions, Pot maintenance procedures Slag pots designed by CSM comply with the requirements of structure dimensions, mechanical properties and guarantee by chemical composition, heat treatment, non-destructive testing and visual inspection against surface.

In the metallurgical and melting fields, a ladle is a vessel used to transport high temperature metal or pour out molten metals. Usually it has three different types, for example, casting ladle, transfer ladle, treatment ladle. Ladles are normally rated by their working capacity rather than by their physical size. Casting ladle: a ladle used to pour molten metal into moulds to produce the casting. Transfer ladle: a ladle used to transfer a large amount of molten metal from one process to another. Typically a transfer ladle will be used to transfer molten metal from a primary melting furnace to either an holding furnace or an auto-pour unit. Treatment ladle: a ladle used for a process to take place within the ladle to change some aspect of the molten metal. A typical example being to convert cast iron to ductile iron by the addition of various elements into the ladle.

1. In 2005, Doocar pioneered the manufacture of pot pulling system, giving auto body shops the same pulling experience as collision benches and frame racks. 2. The high-strength material and strict production process are the key to the quality of the equipment. Doocar has always used Q355B manganese steel and 35CrMo alloy steel. 3. The pulling system has been used in automotive body shops of Mercedes-Benz, BMW, Audi, Volkswagen, Volvo, Toyota, Nissan, GM, Ford, Hyundai and other 4S stations and large-scale body spray centers. 4. In addition to China sales, the equipment has successfully exported in developed countries such as the North American market and the European market.

Doocar collision repair bench Techer 2 is one auto body frame machine that not only can act as car lift but also can do body straightening repair works. The collision repair frame equipment integrates the functions of car lift and bench into one, and integrates the two stations into one. 1. The maximum lifting weight is 4700KG, and the rated load capacity is 4000KG. The height of the bottom of the vehicle is 1900mm from the ground, and the straightening can be performed at multiple angles through the operation of two positions, and straightening at 360° without dead ends. From heavy loads to fast and nimble, we have the perfect lifting and pulling bench for you. 2.The equipment has passed the EU CE safety certification, so you can use it with confidence. 3.The high-strength multi-degree-of-freedom pulling tower has multi-angle straightening function, one-point locking, multi-angle straightening, equipped with imported cylinder pneumatic pump, strong power! Reliable and durable!